Use this reference when you need to identify 24 inch Schedule 10S pipe in a piping layout, material takeoff, fabrication document, or CAD model. The page connects the NPS designation with the DN designation and presents the dimensional and weight data used for preliminary engineering reference.
For design work, read the table together with the terminology notes below. Nominal pipe size is an identification system rather than a direct statement of every measured pipe dimension, while the outside diameter, wall thickness, inside diameter, and mass are the values used to coordinate drawings and calculations.
Schedule 10S pipe 24 inch (DN600) is a large-diameter stainless steel pipe size commonly used in piping design, fabrication, drafting, and engineering reference work. This page provides the standard dimensions, wall thickness, inside diameter, and weight per meter for NPS 24 Schedule 10S pipe based on ASME B36.19.
24 Inch Schedule 10S Pipe Dimensions
- Nominal Pipe Size (NPS): 24 inch
- Diameter Nominal (DN): DN600
- Outside Diameter (OD): 610 mm
- Wall Thickness: 6.35 mm
- Inside Diameter (ID): 597.3 mm
- Pipe Weight: 94.53 kg/m
- Pipe Weight Filled With Water: 374.59 kg/m
- Reference Standard: ASME B36.19
- Pipe Type: Stainless Steel Pipe
Schedule 10S Pipe 24 Inch Data Table
| Pipe Size | DN | OD (mm) | Wall Thickness (mm) | ID (mm) | Weight (kg/m) |
|---|---|---|---|---|---|
| 24 inch | 600 | 610 | 6.35 | 597.3 | 94.53 |
What Does Schedule 10S Mean?
Schedule 10S is a stainless steel pipe schedule covered by ASME B36.19. For the same nominal pipe size, the outside diameter remains fixed while the wall thickness changes with the schedule. The āSā designation is commonly used for stainless steel pipe schedules.
Typical Uses of 24 Inch Schedule 10S Pipe
NPS 24 Schedule 10S pipe is commonly referenced in stainless steel piping systems used in industrial plants, utility lines, water-related systems, food and process facilities, and fabrication work where corrosion resistance and dimensional accuracy are important.
Why Pipe Weight Matters
Pipe weight per meter is useful for transport planning, lifting studies, support design, structural loading, fabrication estimates, and installation planning. In large-diameter stainless steel piping systems, total line weight can significantly affect handling and support requirements.
24 Inch Schedule 10S Pipe Calculation Notes
The listed weight is based on standard stainless steel pipe dimensions using the outside diameter and wall thickness of the pipe. Actual product weight may vary slightly depending on manufacturing tolerance, material grade, and supplier standard.
Frequently Asked Questions
What is the outside diameter of 24 inch Schedule 10S pipe?
The outside diameter is 610 mm.
What is the wall thickness of DN600 Schedule 10S pipe?
The wall thickness is 6.35 mm.
What is the inside diameter of NPS 24 Schedule 10S pipe?
The inside diameter is 597.3 mm.
How much does 24 inch Schedule 10S pipe weigh?
The approximate weight is 94.53 kg/m.
Which standard covers this pipe size?
This dimension data is based on ASME B36.19 for stainless steel pipe.
Conclusion
Schedule 10S pipe 24 inch (DN600) has an outside diameter of 610 mm, wall thickness of 6.35 mm, inside diameter of 597.3 mm, and a weight of 94.53 kg/m. It is a useful reference for piping design, drafting, estimating, and stainless steel fabrication work.
How to Read This Pipe Reference
NPS 24 and DN600 identify the same nominal pipe size using two commonly encountered designation systems. Keeping both labels in a drawing, specification, or procurement document can help prevent confusion when project participants use different conventions.
The outside diameter is useful for layout, fittings, clearances, and support coordination. The wall thickness describes the pipe section used in the reference, while the inside diameter helps with bore, flow-area, and connection checks. These dimensions should be coordinated with the applicable component, material, fabrication, and project requirements before they are used for final design.
Using the Weight Data in Engineering Work
The listed mass per meter can support preliminary material estimates, handling plans, support-load reviews, and routing studies. A complete line assessment may also need to account for fluid contents, insulation, coatings, valves, fittings, flanges, supports, and other attached items. The filled-with-water value in the source table should not be treated as the total operating load for every service condition.
Drafting and CAD Considerations
When preparing a model or isometric drawing, use the stated outside diameter for envelope coordination and the stated wall thickness for section representation where the project level of detail requires it. Confirm end preparations, joint details, fittings, flange dimensions, and material specifications separately; a pipe size reference does not define every connected component.
The downloadable DWG can provide a starting point for drafting workflows. Before issuing a drawing, check units, insertion scale, layer standards, centerline alignment, connection locations, and project-specific title-block requirements.
Related Pipe Reference Topics
This page can be used alongside references for pipe schedules, stainless steel pipe dimensions, pipe fittings, flanges, and piping isometric drafting. Comparing adjacent schedules or related component dimensions is useful when checking a line class or coordinating a complete piping assembly, but each reference should be verified against the governing project documents.
Practical Questions About Using This Reference
Are NPS and DN interchangeable in every document?
They identify the same nominal size here, but project documents may apply different naming conventions. Preserve the designation required by the applicable specification and use both labels when it improves clarity.
Can the listed pipe weight be used as the complete support load?
No. Pipe mass is only one part of a support or structural load review. Contents, fittings, valves, flanges, insulation, supports, test conditions, and other project loads may also need to be included.
Does Schedule 10S specify the stainless steel grade?
The schedule identifies the dimensional wall category for stainless steel pipe; it does not by itself identify the material grade, corrosion performance, welding requirements, or service limits. Those items must come from the project specification and material documentation.
Can the DWG file be used without checking scale?
No. Verify drawing units, insertion scale, layer conventions, and geometry after importing the file into the project environment. CAD content should be checked before it is used for fabrication or issued design documentation.
What should be checked before procurement?
Confirm the nominal size, schedule, material grade, applicable product requirements, end details, length, tolerances, testing, documentation, and supplier data against the approved project specification.