This reference page provides the dimensional and weight data for 24 inch Schedule 80S stainless steel pipe, also identified as NPS 24 and DN600. Use the listed values when checking layout clearances, material take-offs, support loads, fabrication details, and procurement documents.
The dimensional table should be read together with the schedule designation, nominal-size terminology, and the referenced standard. For related design work, compare this pipe data with the dimensions of compatible stainless steel fittings, flanges, valves, and supports before finalizing a piping arrangement.
Schedule 80S Pipe 24 Inch (DN600) is a stainless steel pipe size used in industrial piping systems where corrosion resistance, standardized dimensions, and reliable wall thickness are important. According to the current page data based on ANSI/ASME B36.19, this pipe size has an outside diameter of 610 mm, an inside diameter of 584.6 mm, a wall thickness of 12.7 mm, and a pipe weight of 187.07 kg/m.
24 Inch Schedule 80S Pipe Dimensions
The following dimensions are listed for NPS 24 Schedule 80S pipe, which corresponds to DN600 in metric designation.
- Pipe Size: NPS 24 Inch
- DN Size: DN600
- Outside Diameter (OD): 610 mm
- Inside Diameter (ID): 584.6 mm
- Wall Thickness: 12.7 mm
- Pipe Weight: 187.07 kg/m
- Pipe Weight Including Water: 455.34 kg/m
- Reference Standard: ANSI/ASME B36.19
Schedule 80S Pipe 24 Inch (DN600) Data Table
| Pipe Schedule | NPS | DN | OD (mm) | ID (mm) | Wall Thickness (mm) | Weight (kg/m) |
|---|---|---|---|---|---|---|
| 80S | 24 Inch | 600 | 610 | 584.6 | 12.7 | 187.07 |
What Is Schedule 80S Pipe?
Schedule 80S is a stainless steel pipe schedule designation commonly referenced under ASME B36.19. In piping design, the schedule identifies the wall thickness series for a given nominal pipe size. For engineers, fabricators, and buyers, this helps confirm dimensional compatibility, estimate weight, and coordinate pipe with fittings, flanges, and supports.
Common Uses of 24 Inch Schedule 80S Pipe
24 inch Schedule 80S pipe is commonly used in large stainless steel piping systems where good corrosion resistance, strength, and dependable wall thickness are required. This size is often selected for projects that need high flow capacity together with standard dimensional data for design and procurement work.
- Process piping systems in industrial and chemical plants
- Water transmission lines for large-volume piping service
- Cooling water and utility piping in factories and plant facilities
- Marine and offshore piping where stainless steel is preferred
- Food and beverage plants requiring corrosion-resistant piping materials
- Pharmaceutical facilities using stainless steel process lines
- Pump suction and discharge piping for large flow systems
- Pipeline replacement and upgrade work where standard pipe dimensions are needed
In practical use, designers may refer to this pipe size when checking flow capacity, support loading, transport weight, and piping layout coordination. Final pipe selection should always be reviewed against project pressure, temperature, fluid service, and material requirements.
Why OD, ID, Thickness, and Weight Matter
Knowing the exact OD, ID, wall thickness, and weight is useful for many engineering and construction tasks. These values help with pipe support design, material take-off, transport planning, welding preparation, and installation work. Weight data is also useful when estimating lifting requirements and total line load.
NPS 24 and DN600 Explained
NPS means nominal pipe size in inch units, while DN means diameter nominal in metric units. The current page identifies this pipe as NPS 24 and DN600, which is the standard naming format commonly used in piping documents, drawings, and procurement specifications.
Conclusion
Schedule 80S Pipe 24 Inch (DN600) is a large stainless steel pipe size listed on the current page with 610 mm OD, 584.6 mm ID, 12.7 mm wall thickness, and 187.07 kg/m weight. It is a useful reference for piping engineers, designers, and buyers who need standard dimensional and weight data for stainless steel pipe selection and project coordination.
How to Use This Pipe Reference
The outside diameter is the primary envelope dimension for routing, clamps, sleeves, supports, and connection coordination. The inside diameter helps describe the available flow passage, while the wall thickness is used in fabrication, welding, corrosion-management reviews, and engineering checks.
The listed pipe weight is useful for estimating handling requirements and installed line loading. The water-inclusive figure is a reference condition for a line containing water; actual operating loads can differ with the conveyed fluid, contents, insulation, valves, and other attached components.
Schedule, Nominal Size, and Project Checks
NPS 24 and DN600 are identification systems used in drawings, specifications, and purchasing documents. They identify the nominal pipe size rather than replacing a dimensional check against the listed outside diameter, inside diameter, and wall thickness.
Schedule 80S describes a stainless steel wall-thickness series for the nominal size. It should not be treated as a complete design selection by itself. Material grade, corrosion conditions, design pressure, temperature, joining method, fabrication requirements, and the governing project specification still need review by the responsible engineer.
Coordination With Drawings and Components
Before issuing a layout or fabrication package, coordinate this pipe reference with the project’s piping class, fitting and flange dimensions, weld details, support arrangement, insulation allowance, and access requirements. The downloadable DWG can support drafting and preliminary coordination, but the project team should verify units, drawing scale, connection details, and revision status before using it for fabrication.
For broader reference work, this page can be used alongside resources covering pipe schedules, NPS and DN conversion, pipe fittings, flange dimensions, and piping CAD blocks.
Frequently Asked Questions
What is Schedule 80S Pipe 24 Inch?
It is a stainless steel pipe identified as NPS 24 and DN600, with the page’s dimensional and weight data listed under the Schedule 80S designation.
What does 80S mean?
Schedule 80S identifies a stainless steel wall-thickness series for a specified nominal pipe size. It is a dimensional designation and does not, by itself, identify the material grade or establish a complete pressure-design rating.
Are NPS 24 and DN600 the same pipe size?
They are the inch-based and metric nominal designations used for the pipe covered on this page. Always use the listed dimensional data when checking physical fit and component compatibility.
Why are both pipe weight and pipe weight including water shown?
The pipe weight represents the pipe reference condition, while the water-inclusive value indicates the listed condition when the pipe contains water. Actual installed loading should also account for the service fluid and attached piping components.
Can the DWG file be used directly for fabrication?
The DWG is a drafting reference. Confirm its units, revision, connection details, project specifications, and fabrication requirements before relying on it for construction or manufacturing.